India bit's own miner

1.

Bitmine is real

bitcoin is proced by mining. Every 10 minutes, the miners of the whole network work out an arithmetic problem together. Whoever works out the answer first is equivalent to digging into this block, and the miner can get the bitcoin reward of system rebirth

after bitcoin is g in the mine, the income is distributed according to the proportion of the mine's computing power, so as to ensure a more stable input-output

every other time point, bitcoin system will generate a random code on the system node. All computers in the Internet can search for this code. Whoever finds this code will generate a block and then get a bitcoin. This process is often called mining. Computing this random code requires a lot of GPU operations, so the miners purchase a large number of graphics cards to get bitcoin profits more quickly, which is also an important reason for the recent shortage of graphics cards

2. Bitcoin is a winner take all, and you can only get profits if your computing power reaches a certain level. Therefore, it is suggested that ordinary retail investors should find a reliable exchange, such as okex exchange, to purchase directly.

3. Yes, as long as it's a high configuration graphics card. Now the mining machine starts with 480. The high configuration can earn some money, but the low configuration can't change the electricity charge. N card's computing power is not enough, a card is much higher. You can register in the mine pool first. If the computing power is too low, it will become an invalid node. If you use a home computer, you'd better use three graphics cards. There is little hope of making money.

4. I advise you not to. It's expensive and it consumes a lot of power. It's open all day long.

5. When installing the disc feeder, the user should first install the main bearing. In order to avoid aggravating the wear between the shoulder of the hollow journal and the bearing liner, the elevation difference of the base plate of the two main bearings should be kept within 0.25 mm per meter. Secondly, install the barrel of the grinding machine. According to the specific conditions, the pre assembled whole barrel can be directly installed, or it can be installed in several parts. The journal and the center line of the grinding machine should be checked and adjusted. The concentric error must be less than 0.25m per meter of length. After the installation of transmission parts (pinion, shaft coupling, recer, motor, etc.). In the process of installation, measurement and adjustment should be carried out according to the proct technical standards. Check the radial runout of the ring gear and the meshing performance of the pinion; Concentricity of recer and pinion; And the concentricity of motor and recer. When all the installation standards meet the requirements, the foundation bolts can be tightened and the main bearing base plate can be poured
before the installation of the disc feeder, it is necessary to check the foundation position and geometric size according to the parameter table, and make sure there is no error before the installation. The oil, gravel, soil and water on the surface of the equipment foundation and in the reserved hole of the anchor bolt shall be removed. The thread and nut of the embedded anchor bolt shall be protected, and the surface of the place where the pad iron is placed shall be chiseled flat. Make corresponding records after unpacking inspection and acceptance of equipment parts. The installation shall be carried out according to the proct manual. During the installation, the position shall be found according to the center of the silo, and the deviation of the center distance shall not exceed 5mm; The disc must be in a horizontal position with a deviation of not more than 0.5/1000. Then, the channel steel column is fixed at the lower part of the silo, and the feeding pipe is connected with the screw brake; Turn the V-belt by hand to check whether it operates flexibly; Check the lubricating height in the turbine recer and inject proper amount of lubricating oil into the lubricating points
before the disc feeder equipment is put into proction, the necessary training should be given to the operators to make them master the correct operation process. Only in this way can the service life of the equipment be prolonged and the proction capacity of the equipment be improved. So what is the specific operation process
1. Employees can only operate the equipment after wearing relevant protective equipment It is very necessary, many accidents are e to the lack of protection for personnel)
2. Before starting the machine, check whether the disc is in the horizontal position, and use hand turning to check the operation flexibility
3. Add lubricating oil before starting. At this time, check the rotation direction of the disc to make sure that the motor wiring is correct
4. Check for periodic noise and oil leakage
5. Check the temperature rise of bearing and lubricating oil to make sure it is within the normal range
6. Check the position of scraper and movable sleeve before operation
7. During operation, the spiral gate should be opened after the disc transmission is stable, and the spiral gate should be closed before stopping
8. Always check the lubrication, bearing operation and temperature rise of each part. If there is overheating, it should be eliminated immediately. If necessary, it should be stopped for treatment
9. During long-term operation, the wear of scraper, movable sleeve, disc worm gear, worm, V-belt and seal should be inspected regularly for timely adjustment, maintenance or replacement. Adjustment, repair and other operations are not allowed when the equipment is in operation
10. Clean the equipment and the surrounding area before each shift
lubrication of disc feeder
firstly, thin oil splash lubrication should be used for disc feeder, and the lubricating oil should be determined comprehensively according to the place of use and air temperature conditions, generally gear oil can be used
secondly, ensure that the oil level in the exciter is higher than the oil level (it can be filled through the joint and elbow), and replace it every 3 to 6 months. Pay attention to clean gasoline or kerosene to clean the oil tank, bearing raceway and gear surface when changing the oil
in addition, other vulnerable and easily worn parts should be cleaned and lubricated in time to prevent the wear from affecting the work of the equipment and rece the proction cost.

6. I think Qiu Han is the founder of business chain network
Shenzhen business chain network technology Co., Ltd. was established on November 1, 2017<
Qiu Han, legal representative,
the business scope includes: development and sales of blockchain software and information system software; Electronic Commerce; Development and sales of computer software and hardware, peripheral equipment, electronic procts and information system software; Information technology consulting; Information transmission, software and information technology service instry; Domestic trade (excluding exclusive, monopolized and controlled commodities); To engage in import and export business (except for the items prohibited by laws, administrative regulations and decisions of the State Council, and the restricted items can only be operated after obtaining permission).

7. Sichuan is the most concentrated mining area in China, so Cheng also has a lot of mining machine maintenance points. Yinbit has a maintenance center in Cheng, which is also the official authorized maintenance of Shenma and Xindong. Shenma baonei machines can be repaired free of charge, and Xindong all series of mining machines can be repaired.

8. It can be understood as a kind of distributed computing, but I don't think it can be called & quot; Paid & quot;, The key of bitcoin is to admit the value of the code, As long as the bitcoin system does not collapse, those who accumulate bitcoin can profit from the fluctuation of the value of bitcoin and real currency
hope to adopt it