Ant A3 miner can't find IP

1. Go directly to ask the miner, they will tell you, or send some tutorials on the Internet. bitcoin home. I remember that there were all kinds of mining machines before. You can check them out. I hope I can help you.

2. 1
if all the cables are connected, we can turn on any connected PC at this time. Turn on the network neighborhood property
2
and then turn on the local connection property
3
and then turn on the TCP / IP protocol property

3. You mean game currency. The circulation range of game currency is fixed. It can only be used in fixed games or game malls. The price is stable and the fluctuation is small. Unlike bitcoin, Ruitai coin and Laite coin, the price is not fixed and fluctuates greatly.

4. There is something wrong with the mobile phone system. Reset down the normal management of the phone is good
just download app and Google software first
connect the mobile phone to the computer, select the stable setting of the tool, and the mobile phone will be OK
click the mobile phone system upgrade version on the mobile phone to set it to the latest one
that will ensure that the mobile phone is updated to the latest version
in this way, you can enter the management interface and operate normally.

5.

As shown in the figure,

the reset button is located on the right side of the network port, next to the red and green lights

after the machine is powered on, wait 2 minutes for the miner to start up, press and hold the reset button for 10 seconds (gently poke in with a pen or toothpick, and the hand can't reach the position), release the power, and then power on after 1 minute

the IP address of S7 mining machine is reset

6.

Then, why can Wen Qiao's tomb be preserved so well

this is entirely e to Wen Qiao's outstanding contribution. He considered for the common people and did a lot of good things for the country and the people. Naturally, the common people would not forget him. They often went to the grave to worship him, and asked the descendants to protect the hero's grave

Therefore, in the eyes of later generations, Wen Qiao's status is still very high

7. Although it is copied, it is still useful<

there are hundreds of commonly used subnet masks

here we only introce the two most commonly used subnet masks, which are "255.255.255.0" and "255.255.0.0"

1. Network with subnet mask of "255.255.255.0": the last number can vary from 0 to 255, so 256 IP addresses can be provided. However, the number of available IP addresses is 256-2, that is 254, because the host number cannot be all "0" or all "1"

2. Network with subnet mask of "255.255.0.0": the last two numbers can be changed arbitrarily from 0 to 255, and 2552 IP addresses can be provided. However, the number of available IP addresses is 2552-2, that is 65023

the subnet mask setting of IP address is not arbitrary. If the subnet mask is set too large, that is to say, the scope of the subnet is expanded. According to the subnet routing rules, the data sent to the destination machine that is not in the same subnet as the local machine will be considered to be in the same subnet because of the wrong judgment. Then, the data packet will cycle in the local subnet until it times out and is discarded, so that the data cannot reach the destination machine correctly, Causes the network transmission error; If the subnet mask is set too small, the communication between machines that belong to the same subnet will be regarded as cross subnet transmission, and the data packets will be handed over to the default gateway for processing, which will increase the burden of the default gateway and rece the network efficiency. Therefore, the subnet mask should be set according to the size of the network

if the scale of a network does not exceed 254 computers, it is OK to use "255.255.255.0" as the subnet mask. Now most LANs will not exceed this number, so "255.255.255.0" is the most commonly used IP address subnet mask; The largest primary and secondary school campus network that the author has seen has more than 1500 computers, and the LAN of this scale can use "255.255.0.0"

default subnet mask

in Windows 2000 server, if an IP address is specified for a network card, the system will automatically fill in a default subnet mask. This is a subnet mask automatically generated by Windows 2000 server to save user input time. For example, the IP address "192.168. X.x", which is most commonly used in LAN, has a default subnet mask of "255.255.255.0". In general, the IP address can use the default subnet mask.

8. The router needs to be set up before it can provide multiple computers and mobile devices to share a broadband network at the same time. After the router is set up, the computer can turn on the power and open the web page to access the Internet directly. There is no need to run the dial-up program to operate the dial-up connection alone, and you can access the Internet
the installation and setting methods of routers are similar, please refer to the following settings:
take Tengda's router as an example, if the methods of other brands are similar, the gateway address may be different (for example, 192.168.1.1 gateway, which is generally indicated on the sticker on the bottom of the router, Including user name and password):
1: connect the line: connect the router's WAN port to your home's external network cable, connect your computer to the router's LAN port (there are four, any one can), and power on the router If your router is mini, it has only one port (LAN / WAN port), so when you set it up, power up the router and connect a network cable directly to the computer and the port of the router. After setting it up, pull the network cable from the computer and connect it to your cat)
2: change your computer's IP address to automatic access (of course, it can be fixed IP, but it's troublesome to talk about. If you are interested, check it yourself, or hi me, voice tell you). The steps are: right click "network neighborhood" to select "properties", right click "local connection" to select "properties", Find "Internet Protocol (TCP / IP)" in the "local connection properties page" and then double-click it to open a "Internet Protocol (TCP / IP) properties" page. Change the IP address and DNS to automatic acquisition
3: open IE (the e-icon you usually open on the Internet), enter 192.168.0.1 in the IE address bar, and then press enter to get out a login page with user name and password. The initial user name and password are admin. After you enter, click "OK" to enter the router setting interface

in the left menu bar of router setting interface, there is a "quick setting" option (such as tp link / mercury brand, which seems to be called "setting wizard"), you can click this option, and then a page will come out to let you choose the Internet access mode (if Unicom or telecom gives you an account and password, you can choose PPPoE mode, if a group of IP addresses are given, When you choose the static IP mode, when you fill in the broadband information, remember to fill in the local DNS. If you don't know, you can consult your broadband provider or network), and then click next to save your broadband information (account password or fixed IP address) to the route, Then restart the router (method router menu bar bottom "system tools" - "restart router"), you can access the Internet&# 65279;

I hope I can help you. I hope you can adopt my answer.

9. That group of words, this router is better, now the network is also better.