How to start mining again
Publish: 2021-05-14 07:40:45
1. 1. The poor terrain environment of the mine
the site must be observed before the operation. The mine is located in the high altitude area, with many ramps and sharp bends, so the requirements for the operator are relatively high. In addition, the roads of small private mines are relatively narrow, and there are no stone lined roads. They are all dirt roads, so they can't walk in the rainy season. The picture above is the scene of the open-pit mine project. Special attention should be paid to safety when driving excavators here
2. There are many hidden dangers of excavators responsible for stripping operation
for excavators responsible for stripping operation in mines, they often work on the top of the mountain, which has a high risk index. The mining team and the slag transportation team should try not to be in the same line, otherwise it will be troublesome to roll down the stone. In addition, the excavator responsible for stripping ring mining should not be too many, otherwise the hidden danger is too big
3. Rock excavation in the mine does great harm to the bucket
excavator working in the mine is different from other places, such as digging hard rock in the mine, which does great harm to the bucket. The operators should operate the bucket correctly, adjust the position of the excavator according to the direction of the rock crack, so that the bucket can shovel in smoothly. The force should not be too strong when digging, and the tooth root is easy to break
4. Always obey the command of the safety officer
the safety officer in the mine is also essential. Mining and stripping need at least two safety officers to cooperate, and need to be equipped with whistles and walkie talkies, because the excavator driver can't observe the situation of the rear slope and the surrounding at any time, and the safety officer needs to observe at the highest point. If no one commands, it is dangerous for the rock to fall, This is also one of the hidden dangers of mine safety
5. At the same time of mining, slope repair should be carried out along the way.
open pit mining has the characteristics of heavy workload and many potential safety hazards. Excavator in mining at the same time, but also by the way to repair the slope, because some slope you first repair is not good, to the back to repair it is very difficult. The purpose of repairing the slope is to rece the occurrence of rolling stones and landslides, which requires higher requirements for the manipulator
6. Don't listen to the sound when loading the truck.
when the excavator is working on the slope, you need to pay more attention all the time. Don't turn on the sound in the car or listen to the music. Under the vibration of the excavator in large mines, the loose mud and stones above may be shaken down. If you play it too loud, you can't hear the commander's command or other problems
7. Pay attention to the falling stones after blasting operation
blasting operation is often carried out in mines. Special attention should be paid to safety after blasting, and all-round inspection should be carried out in advance to see if there are loose stones that are about to fall or empty joints caused by blasting. The operator should pay attention to safety, and excavate and mp before entering the working area.
the site must be observed before the operation. The mine is located in the high altitude area, with many ramps and sharp bends, so the requirements for the operator are relatively high. In addition, the roads of small private mines are relatively narrow, and there are no stone lined roads. They are all dirt roads, so they can't walk in the rainy season. The picture above is the scene of the open-pit mine project. Special attention should be paid to safety when driving excavators here
2. There are many hidden dangers of excavators responsible for stripping operation
for excavators responsible for stripping operation in mines, they often work on the top of the mountain, which has a high risk index. The mining team and the slag transportation team should try not to be in the same line, otherwise it will be troublesome to roll down the stone. In addition, the excavator responsible for stripping ring mining should not be too many, otherwise the hidden danger is too big
3. Rock excavation in the mine does great harm to the bucket
excavator working in the mine is different from other places, such as digging hard rock in the mine, which does great harm to the bucket. The operators should operate the bucket correctly, adjust the position of the excavator according to the direction of the rock crack, so that the bucket can shovel in smoothly. The force should not be too strong when digging, and the tooth root is easy to break
4. Always obey the command of the safety officer
the safety officer in the mine is also essential. Mining and stripping need at least two safety officers to cooperate, and need to be equipped with whistles and walkie talkies, because the excavator driver can't observe the situation of the rear slope and the surrounding at any time, and the safety officer needs to observe at the highest point. If no one commands, it is dangerous for the rock to fall, This is also one of the hidden dangers of mine safety
5. At the same time of mining, slope repair should be carried out along the way.
open pit mining has the characteristics of heavy workload and many potential safety hazards. Excavator in mining at the same time, but also by the way to repair the slope, because some slope you first repair is not good, to the back to repair it is very difficult. The purpose of repairing the slope is to rece the occurrence of rolling stones and landslides, which requires higher requirements for the manipulator
6. Don't listen to the sound when loading the truck.
when the excavator is working on the slope, you need to pay more attention all the time. Don't turn on the sound in the car or listen to the music. Under the vibration of the excavator in large mines, the loose mud and stones above may be shaken down. If you play it too loud, you can't hear the commander's command or other problems
7. Pay attention to the falling stones after blasting operation
blasting operation is often carried out in mines. Special attention should be paid to safety after blasting, and all-round inspection should be carried out in advance to see if there are loose stones that are about to fall or empty joints caused by blasting. The operator should pay attention to safety, and excavate and mp before entering the working area.
2. The difference between the mining version and the ordinary version of the excavator is that the thickness and strength of the steel plate of the big frame are the same. The hydraulic pump and engine of the excavator with the same configuration are the same, but the tuning power is slightly different. The mining version is more resistant to operation, and the ordinary version is suitable for excavation and infrastructure construction. A typical mine excavator is Carter
3. 1. The poor terrain environment of the mine < br > before operation, the site must be observed. The mine is located in a high altitude area, with many ramps and sharp bends, so the requirements for the operator are relatively high. In addition, the roads of small private mines are relatively narrow, and there are no stone lined roads. They are all dirt roads, so they can't walk in the rainy season. The picture above is the scene of the open-pit mine project. Special attention should be paid to safety when driving excavators here< Br > 2. There are many hidden dangers of excavators responsible for stripping operation < br > for excavators responsible for stripping operation in mines, they often work on the top of the mountain, which has a high risk index. The mining team and the slag transportation team should try not to be in the same line, otherwise it will be troublesome to roll down the stone. In addition, the excavator responsible for stripping ring mining should not be too many, otherwise the hidden danger is too big< Br > 3. Rock excavation in mines does great harm to the bucket < br > excavators working in mines are different from other places, such as digging hard rock in mines, which does great harm to the bucket. The operators should operate the bucket correctly, adjust the position of the excavator according to the direction of the rock crack, so that the bucket can shovel in smoothly. The force should not be too strong when digging, and the tooth root is easy to break< < br > 4. Always follow the direction of the safety officer < br > the safety officer in the mine is also essential. Mining and stripping need at least two safety officers to cooperate, and need to be equipped with whistles and walkie talkies, because the excavator driver can't observe the situation of the rear slope and the surrounding at any time, and the safety officer needs to observe at the highest point. If no one commands, it is dangerous for the rock to fall, This is also one of the hidden dangers of mine safety< The open pit mine has the characteristics of heavy workload and many potential safety hazards. Excavator in mining at the same time, but also by the way to repair the slope, because some slope you first repair is not good, to the back to repair it is very difficult. The purpose of repairing the slope is to rece the occurrence of rolling stones and landslides, which requires higher requirements for the manipulator< Br > 6. Don't listen to the sound when loading the truck. < br > when the excavator is working on the slope, you need to pay more attention all the time. Don't turn on the sound in the car or listen to the music. Under the vibration of the excavator in large mines, the loose mud and stones above may be shaken down. If you play it too loud, you can't hear the commander's command or other problems< Br > 7. Pay attention to the falling stones after blasting operation < br > blasting operation is often carried out in mines. Special attention should be paid to safety after blasting, and all-round inspection should be carried out in advance to see if there are loose stones that are about to fall, or virtual joints caused by blasting. The operator should pay attention to safety, and the excavator and self unloading can enter the working area after ensuring safety.
4. If the boss owes you money, you can only ask the boss for it. There is no contradiction between buying excavators and paying for them.
5. There are few excavators for coal mining. 2. Clean up the earthwork and dig it away. 3. Rescue the accident. 4. Repair the road. Anyway, there are many things. The excavation in the coal mine is very big. We should adopt it
6. 
Although online shopping is very mature now, it still has some disadvantages, especially in the area of digital electronic procts. Because it is impossible to achieve the pre-sales experience of procts, it is entirely up to the customers to collect information by themselves. However, it is not only from the simple online access that we can obtain the gateway. We need to accumulate practice to obtain experience, In particular, these need certain professional things. Some people say that physical stores are not reliable, but online shopping must be reliable? Not necessarily
The
picture comes from oneself
if the technology is not high, it will not vomit bad
7. Report the situation to the Department seizing the machine, provide the lease contract, and return the property that is not illegal to the owner
8. You can delete it directly, or ask the customer service every day to help cancel the order.
9. The meaning of mine risk elimination is that if there is a big rock or loose rock on it and you dare not dig under it, you have to build a road from the side to carry out risk elimination.
Hot content