How to make water cooled miner
Publish: 2021-05-14 00:51:07
1. First plan, then design, then purchase materials, finally assemble and debug.
2. 1. Seal the radiator under the fan in the main engine, leave a channel in the middle, and then connect two joints respectively, which must be set in the type of bottom in and high out.
2 buy a meter of transparent rubber tube, put the radiator at the bottom in the front in order, and connect the radiator in series.
3 buy a small water pump, and a water cup should also be installed with a pipe joint of one in and one out; The water pump should be placed in the middle of the whole host machine.
4 when the inlet and outlet are all arranged, buy another 0.8cm straight (thin) copper pipe 2m, and make it mm Type after heating. Make a single row with 0.4cm between each pipe, and three or four rows. However, one side must be flat. The motor can see and do it by itself, and the position can be seen and done by itself, It can be installed externally.
5 after the installation of each device, buy the special liquid for water cooling of the computer to prevent water leakage from burning the motherboard,
6 start the computer and test the temperature of each hardware.
if the temperature is very low, then run the big game and check the temperature at any time. If the temperature is good after running for more than three hours, it will be in place. What if the temperature rises slowly,
that means you have to install a fan. Anyway, your CPU fan is useless.
just glue it to the middle of the plane with AB glue (three yuan each). If the 2m long thin copper tube plus a CPU fan can't dissipate heat, no matter how good the water cooling is, it's useless.
moreover, if you add a fan, it's just the sound of a fan. In addition, the sound of the CPU fan is not very loud, The main reason is that the sound of the power fan is the loudest, so there won't be any sound! I just made one, and the result is still very good. Cpu40 ~ 50 degrees (pd805), graphics card 50 ~ 55 degrees (7300le garbage), Beiqiao (35 ~ 45) hard disk was not installed, and it cost more than 200 yuan. It cost 130 yuan to weld the heat sink and then make the interface. No one will do it for you if you don't give some money. I can't do it myself. I only know how to make it good-looking, but I don't think it's good-looking after welding, Stick some flower pictures on it, it's still very nice! Friends who think they can try to do it!
2 buy a meter of transparent rubber tube, put the radiator at the bottom in the front in order, and connect the radiator in series.
3 buy a small water pump, and a water cup should also be installed with a pipe joint of one in and one out; The water pump should be placed in the middle of the whole host machine.
4 when the inlet and outlet are all arranged, buy another 0.8cm straight (thin) copper pipe 2m, and make it mm Type after heating. Make a single row with 0.4cm between each pipe, and three or four rows. However, one side must be flat. The motor can see and do it by itself, and the position can be seen and done by itself, It can be installed externally.
5 after the installation of each device, buy the special liquid for water cooling of the computer to prevent water leakage from burning the motherboard,
6 start the computer and test the temperature of each hardware.
if the temperature is very low, then run the big game and check the temperature at any time. If the temperature is good after running for more than three hours, it will be in place. What if the temperature rises slowly,
that means you have to install a fan. Anyway, your CPU fan is useless.
just glue it to the middle of the plane with AB glue (three yuan each). If the 2m long thin copper tube plus a CPU fan can't dissipate heat, no matter how good the water cooling is, it's useless.
moreover, if you add a fan, it's just the sound of a fan. In addition, the sound of the CPU fan is not very loud, The main reason is that the sound of the power fan is the loudest, so there won't be any sound! I just made one, and the result is still very good. Cpu40 ~ 50 degrees (pd805), graphics card 50 ~ 55 degrees (7300le garbage), Beiqiao (35 ~ 45) hard disk was not installed, and it cost more than 200 yuan. It cost 130 yuan to weld the heat sink and then make the interface. No one will do it for you if you don't give some money. I can't do it myself. I only know how to make it good-looking, but I don't think it's good-looking after welding, Stick some flower pictures on it, it's still very nice! Friends who think they can try to do it!
3. Beginners don't recommend DIY water cooling unless you have a lot of money to go directly to high-end equipment
1 there are many details, such as bubble discharge, pressure, non circulation, etc
2 it is easy to spend more money if the collocation is not good
when I first came into contact with water cooling, I spent nearly 4000, but the effect did not improve much.
1 there are many details, such as bubble discharge, pressure, non circulation, etc
2 it is easy to spend more money if the collocation is not good
when I first came into contact with water cooling, I spent nearly 4000, but the effect did not improve much.
4. Unknown_Error
5. A typical water cooling system must have the following components: water cooling block, circulating liquid, water pump, pipe and water tank or heat exchanger. The water cooling block is a metal block with a water channel inside, which is made of copper or aluminum. It contacts with the CPU and will absorb the heat of the CPU. The circulating liquid flows in the circulating pipeline under the action of the water pump. If the liquid is water, it is known as the water cooling system. The liquid that has absorbed the heat of CPU will flow away from the water cooling block on CPU, and the new low-temperature circulating liquid will continue to absorb the heat of CPU. The water pipe connects the water pump, the water cooling block and the water tank. Its function is to make the circulating liquid circulate in a closed channel without leakage, so that the liquid cooling system can work normally. The water tank is used to store the circulating liquid. The heat exchanger is a device similar to the heat sink. The circulating liquid transfers heat to the heat sink with large surface area, and the fan on the heat sink takes away the heat flowing into the air
the essence of water cooling and air cooling is the same, but water cooling uses circulating liquid to transport the heat of CPU from the water cooling block to the heat exchanger and then radiate it, replacing the homogeneous metal or heat pipe of air cooling, and the heat exchanger part is almost a of air cooling heat exchanger. There are two characteristics of water cooling system: balance the heat of CPU and low noise. Because the specific heat capacity of water is very large, it can absorb a lot of heat and keep the temperature unchanged. The temperature of CPU in the water cooling system can be well controlled, and sudden operation will not cause a large instantaneous change in the internal temperature of CPU. Due to the large surface area of the heat exchanger, only a low-speed fan is needed to cool it, Therefore, most of the water cooling is equipped with fans with low speed. In addition, the working noise of the water pump is generally not very obvious, so the overall cooling system is very quiet compared with the air cooling system
water cooling, which is an expensive and complex heat dissipation method, is the strongest operable radiator for PC (liquid nitrogen and other refrigeration methods can not be put into practical use). Explorative overclocking players started to use it a few years ago to create overclocking limit records, and the proct itself has changed from the early self-made type to the mass proction by professional manufacturers, And into the retail channel sales. With the expansion of proction scale and the graal accumulation of design and manufacturing experience, we have been able to buy quite cheap brand-name water-cooled radiators. Their value is no longer the same as before, or even more than the sum of CPU and motherboard prices. In addition to the attractiveness of price, the humanized design of the latest water-cooled procts has also made considerable progress, Various reasons have contributed to the situation that the water-cooled radiator can enter the chassis of ordinary DIY players.
the essence of water cooling and air cooling is the same, but water cooling uses circulating liquid to transport the heat of CPU from the water cooling block to the heat exchanger and then radiate it, replacing the homogeneous metal or heat pipe of air cooling, and the heat exchanger part is almost a of air cooling heat exchanger. There are two characteristics of water cooling system: balance the heat of CPU and low noise. Because the specific heat capacity of water is very large, it can absorb a lot of heat and keep the temperature unchanged. The temperature of CPU in the water cooling system can be well controlled, and sudden operation will not cause a large instantaneous change in the internal temperature of CPU. Due to the large surface area of the heat exchanger, only a low-speed fan is needed to cool it, Therefore, most of the water cooling is equipped with fans with low speed. In addition, the working noise of the water pump is generally not very obvious, so the overall cooling system is very quiet compared with the air cooling system
water cooling, which is an expensive and complex heat dissipation method, is the strongest operable radiator for PC (liquid nitrogen and other refrigeration methods can not be put into practical use). Explorative overclocking players started to use it a few years ago to create overclocking limit records, and the proct itself has changed from the early self-made type to the mass proction by professional manufacturers, And into the retail channel sales. With the expansion of proction scale and the graal accumulation of design and manufacturing experience, we have been able to buy quite cheap brand-name water-cooled radiators. Their value is no longer the same as before, or even more than the sum of CPU and motherboard prices. In addition to the attractiveness of price, the humanized design of the latest water-cooled procts has also made considerable progress, Various reasons have contributed to the situation that the water-cooled radiator can enter the chassis of ordinary DIY players.
6. This is very troublesome. You need to prepare the materials first. You can't say it in three or two sentences
however, the simple summary is to stick a hollow iron box with two open ends on the graphics chip, lead two pipes out at both ends, and seal the joint. Then put the two pipes into the bucket and pump water. This is circulating water cooling
however, the simple summary is to stick a hollow iron box with two open ends on the graphics chip, lead two pipes out at both ends, and seal the joint. Then put the two pipes into the bucket and pump water. This is circulating water cooling
7. Is the water in the copper pipe self circulating? Normally, the minimum water temperature of water cooling should be basically the same as that of room temperature, and it is impossible to proce condensation water
but it is also possible that I don't know what copper tube means ·
notebook has a high temperature, and there is a special notebook cooling rack, so you can buy one
but it is also possible that I don't know what copper tube means ·
notebook has a high temperature, and there is a special notebook cooling rack, so you can buy one
8. A radiator, an exhaust fan, a water pipe and a water pump are enough. If you want to save trouble, you can buy an old cabinet air conditioner. When the radiator is installed, there is a fan on it, and then the cold water in the well is pumped up by the water pump. After the radiator is blown out by the fan, it is a water-cooled air conditioner, but it is a little waste of water resources
9. Generally speaking, there are many forms of "household water-cooled air conditioning", some with compressor, some without compressor
for example, "well water + water pump + fan coil" does not have a compressor, which takes away the heat in the room by using the relative low temperature of well water
the usual "air conditioning fan" also does not have a compressor. It uses the circulating air to accelerate the evaporation of water, and absorbs the heat in the surrounding air ring the evaporation process to achieve cooling
the household water machine, that is, a small air-cooled hot water unit, is equipped with a compressor
the domestic water source heat pump is equipped with a compressor.
for example, "well water + water pump + fan coil" does not have a compressor, which takes away the heat in the room by using the relative low temperature of well water
the usual "air conditioning fan" also does not have a compressor. It uses the circulating air to accelerate the evaporation of water, and absorbs the heat in the surrounding air ring the evaporation process to achieve cooling
the household water machine, that is, a small air-cooled hot water unit, is equipped with a compressor
the domestic water source heat pump is equipped with a compressor.
10. It's a little difficult to make it by yourself, and the money for purchasing tools is enough for you to buy a good set of water-cooled radiator. I advise you not to make trouble, but to buy a professional water-cooled radiator steadfastly. The DIY type of sc-cs23 liquid cooling suit of Dongyuan is very strong, which contains three cold heads, a sc-750 cold circulating pump and a 240 heat exchanger, All kinds of nozzles and so on, enough for you to DIY
Hot content