Phoenix transportation center to Metro
Publish: 2021-05-27 12:57:44
1. Phoenix transportation center → Guangdong International Hotel, every 30 minutes from 06:30 a.m. to 22:00 p.m.
Phoenix transportation center → Hongcheng Plaza 16:15 16:40 16:50 17:10 17:20 17:45 18:15
Phoenix transportation center → Hongcheng Plaza 16:15 16:40 16:50 17:10 17:20 17:45 18:15
2. I can tell you responsibly that you can earn 4000 + G from 70 to 80 g and equipment for light missions
if you are collecting herbs and plucking skins, The herbs and skins collected can be sold at a good price... If it comes to Saussurea and polar fur... Hahaha
it's easy to make money in the collection profession... WLK... It's suggested to practice mining... That G... Is Hua Hua, eh
if you are collecting herbs and plucking skins, The herbs and skins collected can be sold at a good price... If it comes to Saussurea and polar fur... Hahaha
it's easy to make money in the collection profession... WLK... It's suggested to practice mining... That G... Is Hua Hua, eh
3. Unknown_Error
4. First, you need to understand the three connection modes of virtual machine:
= = = = = = = = = = = = = = = = = = =
VMware provides three working modes, which are bridged (bridge mode), NAT (network address translation mode) and host only (host mode). If you want to use them properly in network management and maintenance, you should first understand these three working modes
1. Bridged (bridging mode)
in this mode, the virtual operating system of VMware is just like an independent host in LAN and host, which can access any machine in the network. In bridge mode, you need to manually configure the IP address and subnet mask for the virtual system, and be in the same network segment as the host machine, so that the virtual system can communicate with the host machine. At the same time, because the virtual system is an independent host system in the LAN, you can manually configure its TCP / IP configuration information to access the Internet through the gateway or router of the LAN
the relationship between a virtual system using bridging mode and the host machine is like two computers connected to the same hub. If you want them to communicate with each other, you need to configure the IP address and subnet mask for the virtual system, otherwise they cannot communicate
if you want to use VMware to create a new virtual server in the LAN to provide network services for LAN users, you should choose the bridging mode
2. Host only (host mode)
in some special network debugging environments, it is required to separate the real environment from the virtual environment. In this case, you can use the host only mode. In host only mode, all virtual systems can communicate with each other, but the virtual system and the real network are isolated
prompt: in host only mode, the virtual system and host machine system can communicate with each other, which is equivalent to the interconnection of the two machines through twisted pair
in host only mode, the TCP / IP configuration information of virtual system (such as IP address, gateway address, DNS server, etc.) is dynamically allocated by the DHCP server of VMnet1 (host only) virtual network
if you want to use VMware to create a virtual system that is isolated from other machines in the network and do some special network debugging work, you can choose the host only mode
3. Nat (network address translation mode)
using NAT mode is to let the virtual system access the public network through the host machine's network with the help of NAT (network address translation) function. In other words, using NAT mode can achieve access to the Internet in the virtual system. The TCP / IP configuration information of the virtual system in NAT mode is provided by the DHCP server of VMnet8 (NAT) virtual network, which can't be modified manually, so the virtual system can't communicate with other real hosts in this LAN. The biggest advantage of using NAT mode is that the virtual system access to the Internet is very simple, you do not need any other configuration, just need the host machine can access the Internet
if you want to use VMware to install a new virtual system, and you can directly access the Internet without any manual configuration in the virtual system, it is recommended that you use NAT mode
tip: the above mentioned VMnet8 virtual network in NAT mode, VMnet1 virtual network in host only mode, and vmnet0 virtual network in bridged mode are all generated by automatic configuration of VMware virtual machine, and do not need to be set by users themselves. VMnet8 and VMnet1 provide DHCP service, while vmnet0 virtual network does not
= = = = = = = = = = = = = = = = = = =
it is recommended that all the virtual machines of the building owner use the same connection mode. Otherwise, there will be many problems
= = = = = = = = = = = = = = = = = = =
VMware provides three working modes, which are bridged (bridge mode), NAT (network address translation mode) and host only (host mode). If you want to use them properly in network management and maintenance, you should first understand these three working modes
1. Bridged (bridging mode)
in this mode, the virtual operating system of VMware is just like an independent host in LAN and host, which can access any machine in the network. In bridge mode, you need to manually configure the IP address and subnet mask for the virtual system, and be in the same network segment as the host machine, so that the virtual system can communicate with the host machine. At the same time, because the virtual system is an independent host system in the LAN, you can manually configure its TCP / IP configuration information to access the Internet through the gateway or router of the LAN
the relationship between a virtual system using bridging mode and the host machine is like two computers connected to the same hub. If you want them to communicate with each other, you need to configure the IP address and subnet mask for the virtual system, otherwise they cannot communicate
if you want to use VMware to create a new virtual server in the LAN to provide network services for LAN users, you should choose the bridging mode
2. Host only (host mode)
in some special network debugging environments, it is required to separate the real environment from the virtual environment. In this case, you can use the host only mode. In host only mode, all virtual systems can communicate with each other, but the virtual system and the real network are isolated
prompt: in host only mode, the virtual system and host machine system can communicate with each other, which is equivalent to the interconnection of the two machines through twisted pair
in host only mode, the TCP / IP configuration information of virtual system (such as IP address, gateway address, DNS server, etc.) is dynamically allocated by the DHCP server of VMnet1 (host only) virtual network
if you want to use VMware to create a virtual system that is isolated from other machines in the network and do some special network debugging work, you can choose the host only mode
3. Nat (network address translation mode)
using NAT mode is to let the virtual system access the public network through the host machine's network with the help of NAT (network address translation) function. In other words, using NAT mode can achieve access to the Internet in the virtual system. The TCP / IP configuration information of the virtual system in NAT mode is provided by the DHCP server of VMnet8 (NAT) virtual network, which can't be modified manually, so the virtual system can't communicate with other real hosts in this LAN. The biggest advantage of using NAT mode is that the virtual system access to the Internet is very simple, you do not need any other configuration, just need the host machine can access the Internet
if you want to use VMware to install a new virtual system, and you can directly access the Internet without any manual configuration in the virtual system, it is recommended that you use NAT mode
tip: the above mentioned VMnet8 virtual network in NAT mode, VMnet1 virtual network in host only mode, and vmnet0 virtual network in bridged mode are all generated by automatic configuration of VMware virtual machine, and do not need to be set by users themselves. VMnet8 and VMnet1 provide DHCP service, while vmnet0 virtual network does not
= = = = = = = = = = = = = = = = = = =
it is recommended that all the virtual machines of the building owner use the same connection mode. Otherwise, there will be many problems
Hot content