Long distance passenger transport center station to Lushan

1.

Drum washing machine E10 is overheated drum, use precautions:

the power supply voltage should not fluctuate too much (allowed) ± Moreover, Midea's washing machine should be powered by a dedicated line, using a single-phase three hole socket, and the plug should be inserted to the end

the shell of indoor unit should be cleaned frequently. Generally, it can be wiped with clean dry cloth or neutral detergent. It is absolutely not allowed to wash directly with water. If it is wiped with cloth, it should be done after power failure; The indoor temperature can not be adjusted too low, otherwise it is harmful to the human body, and the set temperature should be adjusted appropriately

< H2 > extended information:

drum washing machine has become the main model in the current international washing machine market e to its advantages of low wear, non winding, washable cashmere, silk fabric and large capacity

there are many brands of drum washing machines on the market, which seem to be similar. In fact, different brands of drum washing machines still have differences in their quality and function, so it is necessary to carefully compare them when purchasing

generally, the washing machine is a front door type, which needs to occupy a large space. However, in Chinese families, the washing machine is usually placed in a small kitchen or toilet, which is very inconvenient to use. So consumers need to consider a lot of factors and understand some of the precautions when buying drum washing machine

2.

The reason for "E10" of cygnet drum washing machine: water inflow timeout

Please check:

1. If the water inlet pressure is too low, it can be used after the water pressure returns to normal

If the outlet of the drainage pipe is inserted in the water, the position of the outlet of the drainage pipe can be adjusted not to be in the water

3. Check whether the height of drainage pipe is too low or too high, and re place it between 60-120cm

4. The inlet valve is dirty and blocked, screw off the inlet pipe interface and clean it

if the above methods can not eliminate the fault, report for repair

extended information:

precautions for use of cygnet drum washing machine:

1. It is strictly prohibited to use the washing machine in flammable and explosive environment

2. Please take out coins, keys and other sundries in the clothes before washing, and turn the zipper to the inside of the clothes

3. The wave wheel of the washing machine will not rotate until the water level is set; If you add water manually, you need to add as much water as possible and lower the water level setting

When washing with warm water, the water temperature should not exceed 50 ℃

5. It is strictly forbidden to put children or pile heavy objects on the washing machine

6. Do not put your hand in the bucket before the bucket stops rotating

Do not wash down jacket, raincoat, fishing suit and other similar articles in the washing machine. If you really need to wash similar articles, please cover them with a net before washing

After washing, please turn off the tap and pull out the power plug of the washing machine

resources: cygnet FAQ search - E10 (unable to hyperlink to specific questions, you need to enter E10 in the keyword to search.)

resources: cygnet FAQ search - what are the precautions in the use process

3. It can be predicted that in the future, real currency will be eliminated e to portability and circulation problems. The amount of each person's assets may be a string of virtual currencies, which will still be issued by the central bank, otherwise the country will lose the ability of economic control. bitcoin, on the other hand, does not have a central issuing institution. It is an alternative virtual currency for people to "mine" or trade separately. Therefore, I believe that bitcoin will continue to exist in the future, but it will become a virtual currency that keeps pace with the electronic currency issued by the state. By then, you will be able to see bitcoin on all kinds of electronic platforms.

4. It is very likely that money will become network data, that is, money will be "electronic". However, according to Shanlin financial survey, bitcoin, as the "Internet red" in e-money, has stepped into the "crooked path" and entered the gray area of the trading field. Because bitcoin is difficult to trace, it has become a tool to hide the proceeds of crime, evade foreign exchange control, launder money and other illegal transactions. Shanlin financial experts said that the currency "electronic" still depends on the standardized development of the Internet.

5. Peel force and peel strength belong to two different units and cannot be converted to each other. Peeling force is a kind of force, and its units are n, KGF, GF, LBF, etc. peeling strength is a linear strength unit, which is the force per unit length, and is generally expressed in M / mm, kgf / cm, LBF / in.

6. Peel strength: the maximum force required to peel the bonded materials from the contact surface per unit width. When peeling, the angle is 90 degrees or 180 degrees, and the unit is Newton / meter (n / M). It reflects the bond strength of the material. Such as safety film and glass, mobile phone film
2 influencing factors
when the thickness of the safety film reaches 0.2mm or more, the peel strength becomes smaller. In fact, this is because the angle of 90 or 180 degrees cannot be achieved e to the increase of the thickness of the film, resulting in inconsistent measurement conditions
the adhesive resin of safety film
1. The effect of resin melt index (MI) on peel strength
melt index (MI) is an index of resin fluidity. Generally speaking, the higher the MI of resin, the better the fluidity, the lower the viscosity of the melt film and the greater the adhesion. If the melt index (MI) of the resin is too small and its molecular weight is too large, the fusibility of the resin is relatively poor, and the resin can not bond well with the coated substrate, resulting in the decrease of peel fastness
2. The effect of resin density on peel strength
the lower the density of the resin, the higher the branched chain content, the easier the surface is to be activated, the greater the adhesion, and the better the peel strength
3. The influence of additives and moisture content on peel strength
the additives in the resin, especially the lubricant, have a great influence on the peel strength of the extruded composite film.

7. Peel force and peel strength belong to two different units and cannot be converted to each other

peeling force is a kind of force, and its units are n, KGF, GF, LBF, etc.
peeling strength is a linear strength unit, which is the force per unit length, and is generally expressed in M / mm, kgf / cm, LBF / in

because the peeling force can only be compared under the same conditions,
for example, if the same piece of material is cut into 10 mm wide and 25 mm wide, the peeling force of 25 mm wide will be greater than that of 10 mm wide
therefore, the peel strength is introced, and the same width is used for testing, so that the peel strength of the same material or even different materials can be comparable
instry standards gb2792 and ASTM d3330 have taken 25 mm as the standard width unit, so in the actual test, the peel force and peel strength are equal in value, but their meanings are different

8. 1. Your device is 180 ° Peel strength test
2. The different thickness of glue has obvious influence on the peel strength. For example, if you use glue to paste two pieces of paper, the more the glue, the better. Similarly, 180 ° When testing, the glue is too thick, which is similar to the kinematic viscosity of the side glue. So it is not allowed, must be in accordance with the provisions, coating a certain thickness.