37 / F, block 2, Henglong Plaza, Shanghai Yubo Service Center
Publish: 2021-05-21 03:33:38
1. The watch maintenance center is located in room 3705, building 2, ganghui Henglong Plaza, No.3, Hongqiao Road, Xuhui District, Shanghai. Here are five common reasons for watch travel time error and watch travel time inaccuracy:
1) insufficient power storage: you need to check whether the power is sufficient first. If the amount of motion of the automatic mechanical watch is very small, it may also cause insufficient power storage, You can supplement the power by manually loading the chain, and then observe whether the phenomenon of speed continues
2) insufficient power: if the quartz watch suddenly finds that it is slow, it may be caused by insufficient battery energy, you can send the watch to a special maintenance point to check the power
3) have been hit or hit: the watch is very tight. If it is hit or hit, it may cause internal parts loose and damage, and it may also cause travel time problems. This is to be dealt with in time
4) maintenance required: the lack of oil in the movement or the wear and aging of internal parts may cause travel time problems, which need to be maintained and sent to the designated repair point for maintenance
5) in addition to the above common cases, the watch is magnetized e to the influence of some ambient temperature: if the hairspring of the watch is magnetized, the watch's travel time will be inaccurate.
1) insufficient power storage: you need to check whether the power is sufficient first. If the amount of motion of the automatic mechanical watch is very small, it may also cause insufficient power storage, You can supplement the power by manually loading the chain, and then observe whether the phenomenon of speed continues
2) insufficient power: if the quartz watch suddenly finds that it is slow, it may be caused by insufficient battery energy, you can send the watch to a special maintenance point to check the power
3) have been hit or hit: the watch is very tight. If it is hit or hit, it may cause internal parts loose and damage, and it may also cause travel time problems. This is to be dealt with in time
4) maintenance required: the lack of oil in the movement or the wear and aging of internal parts may cause travel time problems, which need to be maintained and sent to the designated repair point for maintenance
5) in addition to the above common cases, the watch is magnetized e to the influence of some ambient temperature: if the hairspring of the watch is magnetized, the watch's travel time will be inaccurate.
2. Shanghai watch repair service center has a company in Hongyi International Plaza, Huangpu District. It is specially for some valuable watches. It needs to pay more attention to the maintenance in use, regularly clean the stains on the watch case, and maintain the watch every 2-3 years or so. If you want to carry out professional maintenance, I suggest you go to the professional after-sales service center for maintenance, or my home page for consultation. For you to solve with the watch repair, maintenance and cleaning, beauty appraisal and other full process customer service management. Welcome your consultation
3. Watch strap replacement (broken)
(steel) first of all, please look at the arrow on the back of the strap before you are ready to remove it. The belt with arrow is detachable. Secondly, loosen the handle of the belt remover, put the watch strap
into the watch slot, and keep the steel needle of the belt remover aligned with the pinhole, and the steel needle of the belt remover follows the direction indicated by the arrow. At this time, tighten the handle of the belt remover inward, and the
steel needle (ear) connecting the watch strap will be pushed out, and then pull out the ear with pliers
in the process of use, use the steel needle carefully to avoid scratching the watch strap, which will affect the appearance, and be careful not to scratch your hand. After the strap is removed to the size suitable for the wrist,
at this time, the strap that is broken into two sections should be connected. After inserting, the rest of the large section of the riser can be gently knocked with hard material, preferably colloidal hard material, to avoid scratching the strap. After knocking in, use the stripper to slightly push the ear into the concave and fix it
(leather) a tool is necessary to replace the watch strap. One end of the tool is concave, which is used to remove the ear, and the other end is sharp, which is used to clear the hole of the watch strap. If not, flat or small tools can be used instead
there is a metal rod-shaped object on the watch belt, which is called Shenger. There are two springs at both ends of the ear, which are used to clamp the ear of a watch. Therefore, when we remove the
belt, we only need to use the tool concave head to clamp one end of the ear and press it down. The spring is compressed and the length of the ear becomes shorter. So you can take the strap off
when installing a new watch strap, press one end of the ear with a tool and clip the other end into the groove of the ear. Align the pressed ear with the groove on the other side and gently retract the tool to make the ear fit into the groove of the ear. You can replace the watch strap!
(steel) first of all, please look at the arrow on the back of the strap before you are ready to remove it. The belt with arrow is detachable. Secondly, loosen the handle of the belt remover, put the watch strap
into the watch slot, and keep the steel needle of the belt remover aligned with the pinhole, and the steel needle of the belt remover follows the direction indicated by the arrow. At this time, tighten the handle of the belt remover inward, and the
steel needle (ear) connecting the watch strap will be pushed out, and then pull out the ear with pliers
in the process of use, use the steel needle carefully to avoid scratching the watch strap, which will affect the appearance, and be careful not to scratch your hand. After the strap is removed to the size suitable for the wrist,
at this time, the strap that is broken into two sections should be connected. After inserting, the rest of the large section of the riser can be gently knocked with hard material, preferably colloidal hard material, to avoid scratching the strap. After knocking in, use the stripper to slightly push the ear into the concave and fix it
(leather) a tool is necessary to replace the watch strap. One end of the tool is concave, which is used to remove the ear, and the other end is sharp, which is used to clear the hole of the watch strap. If not, flat or small tools can be used instead
there is a metal rod-shaped object on the watch belt, which is called Shenger. There are two springs at both ends of the ear, which are used to clamp the ear of a watch. Therefore, when we remove the
belt, we only need to use the tool concave head to clamp one end of the ear and press it down. The spring is compressed and the length of the ear becomes shorter. So you can take the strap off
when installing a new watch strap, press one end of the ear with a tool and clip the other end into the groove of the ear. Align the pressed ear with the groove on the other side and gently retract the tool to make the ear fit into the groove of the ear. You can replace the watch strap!
4. Langer maintenance center is located in room 3705, 37th floor, building 2, ganghui Henglong Plaza, No.3, Hongqiao Road, Xuhui District, Shanghai.
1. Watch magnetization: watch magnetization is one of the common reasons for watch slow down. Even an antimagnetic watch, even an antimagnetic watch, can't be placed next to some electrical appliances, because some parts of it are not antimagnetic, and will be magnetized over time. Watch magnetization needs to be degaussed by professional watch maintenance organization
2. Lack of power: mechanical watch can be divided into manual winding and automatic winding. Lack of power is often an important reason for the watch to slow down or even stop
the mechanical watch with manual winding can solve the problem by winding, while the watch with automatic winding is mostly e to the lack of wearing time (less than 8-10 hours per day) or the people with little exercise. Ordinary office friends or the elderly often appear mechanical watch power shortage and lead to watch slow situation
3. Insufficient maintenance leads to mechanical failure: daily wearing is not paid much attention, and problems such as collision have occurred, which makes the internal parts of the watch loose and leads to inaccurate travel time of the watch
st and foreign matters cause the gears to jam with each other, and some watches have too much or very little oil, which will make the electronic watch not work well
in case of such faults of stepping motor and gear train, it is necessary to clean, remove foreign matters and refuel. Some parts in the movement are damaged and need to be replaced.
1. Watch magnetization: watch magnetization is one of the common reasons for watch slow down. Even an antimagnetic watch, even an antimagnetic watch, can't be placed next to some electrical appliances, because some parts of it are not antimagnetic, and will be magnetized over time. Watch magnetization needs to be degaussed by professional watch maintenance organization
2. Lack of power: mechanical watch can be divided into manual winding and automatic winding. Lack of power is often an important reason for the watch to slow down or even stop
the mechanical watch with manual winding can solve the problem by winding, while the watch with automatic winding is mostly e to the lack of wearing time (less than 8-10 hours per day) or the people with little exercise. Ordinary office friends or the elderly often appear mechanical watch power shortage and lead to watch slow situation
3. Insufficient maintenance leads to mechanical failure: daily wearing is not paid much attention, and problems such as collision have occurred, which makes the internal parts of the watch loose and leads to inaccurate travel time of the watch
st and foreign matters cause the gears to jam with each other, and some watches have too much or very little oil, which will make the electronic watch not work well
in case of such faults of stepping motor and gear train, it is necessary to clean, remove foreign matters and refuel. Some parts in the movement are damaged and need to be replaced.
5. There is a professional and official after-sales service center in Shanghai. It is located in room 3705, 37th floor, block 2, ganghui Henglong Plaza, Hongqiao Road, Xuhui District. It is accessible to Shanghai Metro Line 1, line 9 and line 11. Get off at Xujiahui Station in Shanghai and get out at entrance 12!
6. If there is something wrong with Wanguo watch, you can take it to (37th floor, building 2, ganghui Henglong Plaza, No.3 Hongqiao Road, Xuhui District, Shanghai) for repair< Maintenance methods of Wanguo watch
1. Regular maintenance of the watch should be carried out every 1-2 years, including replacement of waterproof components, detection of travel time function and movement power consumption, cleaning of movement and maintenance appearance. Such maintenance service will effectively extend the service life of your mechanical watch
2. Do not put the watch on the audio or TV to prevent magnetization
3. Do not put the watch in the wardrobe with camphor pills to prevent the oil from changing
4. Do not touch the watch with corrosive substances, especially acidic substances, which will corrode the watch case
5. The daily maintenance and care of watch is not difficult, as long as you can do these work regularly, I believe that love watch can always keep the best operation state. When it is worn between your wrists, it will certainly better highlight your charm and temperament!
1. Regular maintenance of the watch should be carried out every 1-2 years, including replacement of waterproof components, detection of travel time function and movement power consumption, cleaning of movement and maintenance appearance. Such maintenance service will effectively extend the service life of your mechanical watch
2. Do not put the watch on the audio or TV to prevent magnetization
3. Do not put the watch in the wardrobe with camphor pills to prevent the oil from changing
4. Do not touch the watch with corrosive substances, especially acidic substances, which will corrode the watch case
5. The daily maintenance and care of watch is not difficult, as long as you can do these work regularly, I believe that love watch can always keep the best operation state. When it is worn between your wrists, it will certainly better highlight your charm and temperament!
7. It is not necessary to worry too much that the needle can be replaced if it is dropped or damaged. Because the pointer is installed in layers, the top wheel tube is connected with the second hand, so generally the pointer is lost mostly the second hand. If the pointer of a watch falls off, the crown should be pulled out in time to stop it from walking, so as to prevent the pointer from scratching the watch cover, dial or breaking itself. After pulling out the watch crown, please repair it in time to prevent the watch from entering ash. In general, if there is no internal damage to the watch, the maintenance is relatively easy. If the wheel tube is deformed, broken or parts are worn, the maintenance will be a little more difficult. Pay attention to choose the proper mechanism when installing the watch needle, so as to prevent scratching the dial and recing the waterproof performance of the watch. When installing the needle, put a layer of film on the dial to protect it. A comprehensive waterproof test is needed to install the needle, and the aging waterproof ring needs to be replaced. Watch maintenance center warm reminder: when you use the watch must pay attention to shockproof. Watch is a precise instrument, we need to pay attention to the problem of shockproof and fall proof. Moreover, the watch is particularly delicate, we must pay attention to maintenance on time. If you have any other questions about watch repair or watch maintenance, please call the consulting number.
8. Roger per watch official service center: [Shanghai] [Xuhui District] [Hongqiao Road] [No.3] [ganghui Henglong Plaza] [37th floor, 2 office buildings]
there are many reasons for Roger per's inaccuracy, such as collision, movement gear dislocation, watch magnetization, etc If you have any questions that you don't understand, you can click the avatar hotline]
Roger per's travel time is not accurate. You should check whether the watch is stationary for a long time. The automatic watch depends on the relative motion of the swing to wind up automatically. If it is carried in the hand and is in a relatively static state for a long time, the watch can not wind up automatically, it will lose the ability to walk and stop. The user only needs to swing the watch dozens of times or several times to wind it up (when there is a hand adjustment function), and the travel time can be restored The watch is demagnetized free of charge
there are many reasons for Roger per's inaccuracy, such as collision, movement gear dislocation, watch magnetization, etc If you have any questions that you don't understand, you can click the avatar hotline]
Roger per's travel time is not accurate. You should check whether the watch is stationary for a long time. The automatic watch depends on the relative motion of the swing to wind up automatically. If it is carried in the hand and is in a relatively static state for a long time, the watch can not wind up automatically, it will lose the ability to walk and stop. The user only needs to swing the watch dozens of times or several times to wind it up (when there is a hand adjustment function), and the travel time can be restored The watch is demagnetized free of charge
9. I'll go. What kind of watch is this? We must expose unscrupulous businesses, and don't let netizens die again
Hot content